Plumbing Basics: Before Installing a Bathtub
Plumbing Basics: Before Installing a Bathtub
Blog Article
Are you trying to locate ideas concerning A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and in some cases, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old tub is easily accessible, the job can relocate immediately; if you have to open a wall to eliminate the old bathtub and position the new bath tub, the job is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub and also embeded in the new one. Make certain you have actually qualified yourself for the task and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is much better to think about utilizing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This short article will help you mount a brand-new bathtub in your bathroom if you have actually currently purchased a new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist must make up the following:
Preparing for the Installation
First of all, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to avoid strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is detach the supply of water. After doing so, switch on the taps to drain pipes any water remaining in the system. The process of removing the existing taps can be quite problematic as a result of the limited gain access to that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning during this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Utilizing both wood boards under its feet, place the bath tub in the required position. The wood boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the tub till the spirit level reviews degree.
To install faucets, fit the bottom of the furthest versatile faucet port to the proper supply pipeline by making a compression sign up with; after that do the same for the various other tap.
Turn on the supply of water and examine all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the tub as well as likewise check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as described in the manufacturer's user's manual. Tiling and securing around the bath tub ought to wait until the bathtub has actually been utilized at the very least once as this will resolve it right into its final setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washing machines are in place between the tap as well as the sink. Secure the faucet in place with the manufacturer offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The former kind needs to be connected to the faucet ends first, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break a rigid seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, leading to problems with moisture as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and can securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the ceramic tiles making use of waterproof or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave feedback further down. We'd be delighted to know your views about this piece. In hopes that you visit us again soon. Sharing is nice. You just don't know, you may be doing someone a favor. Thanks for your time spent reading it.
Pipe issues? Connect. Report this page